Sketch

In this tutorial, you’ll learn how each part of that sketch works.

Sketch

A sketch is the name that Arduino and 86Duino use for a program. It’s the unit of code that is uploaded to and run on an Arduino or 86Duino board.

Comments

The first few lines of the Blink sketch are a comment:
/*
* Blink
*
* The basic Arduino example.  Turns on an LED on for one second,
* then off for one second, and so on...  We use pin 13 because,
* depending on your Arduino board, it has either a built-in LED
* or a built-in resistor so that you need only an LED.
*
* http://www.arduino.cc/en/Tutorial/Blink
*/
Everything between the /* and */ is ignored by the Arduino/86Duino when it runs the sketch (the * at the start of each line is only there to make the comment look pretty, and isn’t required). It’s there for people reading the code: to explain what the program does, how it works, or why it’s written the way it is. It’s a good practice to comment your sketches, and to keep the comments up-to-date when you modify the code. This helps other people to learn from or modify your code.

There’s another style for short, single-line comments. These start with // and continue to the end of the line. For example, in the line:

   int ledPin = 13; // LED connected to digital pin 13

the message “LED connected to digital pin 13” is a comment.

Variables

A variable is a place for storing a piece of data. It has a name, a type, and a value. For example, the line from the Blink sketch above declares a variable with the name ledPin, the type int, and an initial value of 13. It’s being used to indicate which Arduino/86Duino pin the LED is connected to. Every time the name ledPin appears in the code, its value will be retrieved. In this case, the person writing the program could have chosen not to bother creating the ledPin variable and instead have simply written 13 everywhere they needed to specify a pin number. The advantage of using a variable is that it’s easier to move the LED to a different pin: you only need to edit the one line that assigns the initial value to the variable.

Often, however, the value of a variable will change while the sketch runs. For example, you could store the value read from an input into a variable. There’s more information in the Variables tutorial.

Functions

A function (otherwise known as a procedure or sub-routine) is a named piece of code that can be used from elsewhere in a sketch. For example, here’s the definition of the setup() function from the Blink example:
void setup()
{
pinMode(ledPin, OUTPUT);      // sets the digital pin as output
}
The first line provides information about the function, like its name, “setup”. The text before and after the name specify its return type and parameters: these will be explained later. The code between the { and } is called the body of the function: what the function does.

You can call a function that’s already been defined (either in your sketch or as part of the 86Duino language). For example, the line pinMode(ledPin, OUTPUT); calls the pinMode() function, passing it two parameters: ledPin and OUTPUT. These parameters are used by the pinMode() function to decide which pin and mode to set.

pinMode(), digitalWrite(), and delay()

The pinMode() function configures a pin as either an input or an output. To use it, you pass it the number of the pin to configure and the constant INPUT or OUTPUT. When configured as an input, a pin can detect the state of a sensor like a pushbutton (refer to the Arduino tutorial). As an output, it can drive an actuator like an LED.

The digitalWrite() functions outputs a value on a pin. For example, the line:

   digitalWrite(ledPin, HIGH);

set the ledPin (pin 13) to HIGH, or 5 volts. Writing a LOW to pin connects it to ground, or 0 volts.

The delay() causes the 86Duino to wait for the specified number of milliseconds before continuing on to the next line. There are 1000 milliseconds in a second, so the line:

   delay(1000);

creates a delay of one second.

setup() and loop()

There are two special functions that are a part of every 86Duino sketch: setup() and loop(). The setup() is called once, when the sketch starts. It’s a good place to do setup tasks like setting pin modes or initializing libraries. The loop() function is called over and over and is heart of most sketches. You need to include both functions in your sketch, even if you don’t need them for anything.

See also

setup()
loop()
pinMode()
digitalWrite()
delay()


Language Reference Home

The text of the 86Duino reference is a modification of the Arduino reference, and is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the reference are released into the public domain.